No.0 Machinery Get a quote +86 135 8587 6500
Home/Products/Plastic Sheet Bending Machines/No.0 Dual-Side Heated Automatic Plastic Bending Machine
PLASTIC SHEET BENDING

No.0 Dual-Side Heated Automatic Plastic Bending Machine

built to orderBoth faces heated, thick sheet folds through.
No.0 Dual-Side Heated Automatic Plastic Bending Machine built to order — thick acrylic displays
0.8–20 mm(0.03 in–0.79 in) (acrylic 0.5–20 mm (0.02 in–0.79 in))Sheet thickness
1.2 / 1.8 / 2.4 / 3 m(9.8 ft)Table length
dual-side, independent temperaturesHeating
air, water circuit optionalCooling

Heat thick sheet from one side and the outside scorches before the core softens — the fold cracks. Two heater banks, above and below, soften the full thickness at once, so 0.8–20 mm sheet folds through in a single pass.

What it solves

01
Temperature gradient

Outside burnt, inside hard: the corner cracks.

Wrinkled inner face

The compression side never gets hot enough.

Grooving required

If it will not fold, the usual answer is to machine a groove — weakening the part.

Core value

02
01

0.8–20 mm in one pass.

02

No grooving needed.

03

Water-cooled top platen, no surface marks.

How it works

03
  1. 01
    Top and bottom heating

    Two heater banks work on the same line, each with its own temperature.

  2. 02
    Water-cooled top platen

    The upper aluminium platen is water cooled, holding the heating line stable.

  3. 03
    Protective sleeve

    An insulating sleeve keeps the upper heater from marking the sheet.

  4. 04
    Adjustable heater gap

    Wide for thick sheet, narrow for thin, so heat is even.

Specifications

04
Sheet thickness0.8–20 mm (0.03 in–0.79 in) (acrylic 0.5–20 mm (0.02 in–0.79 in))
Table length1.2 / 1.8 / 2.4 / 3 m (9.8 ft)
Heatingdual-side, independent temperatures
Coolingair, water circuit optional
Voltage / power220 V / 3 kW
Air pressure0.5 MPa

Advantages

05

Forming

  • Full thickness softened: thick sheet folds in one pass.
  • No cracking outside, no wrinkling inside.
  • No grooving, so the parent material stays intact.

Operation

  • Top/bottom temperature, dwell and angle set on the panel.
  • Automatic and manual modes.
  • Protective sleeve keeps the surface unmarked.

What it bends

06
Thick acrylic displaysHeavy-duty casesAutomotive interior partsAppliance panels

Machine detail

No.0 Dual-Side Heated Automatic Plastic Bending Machine — detail 1 (built to order)No.0 Dual-Side Heated Automatic Plastic Bending Machine — detail 2 (built to order)

Video

Send a sample sheet

Post a 200 × 200 mm offcut with material and thickness noted; we bend it to your angle and send photos plus video within 48 hours.

Request a trial bend

Also known as

07
Dual-Side Heating BenderDouble-Sided Heating Bending MachineThick Sheet BenderHeavy Gauge Sheet BenderTop and Bottom Heating BenderThick Acrylic Bender

All names above refer to this machine — see the full alias index.

FAQ

08
What is the maximum thickness?

0.8–20 mm; acrylic from 0.5 mm.

Why heat both sides?

Heating one side scorches the outside before the core softens, and the fold cracks.